How To Remove Rivets Lower Ball Joint

We got the rivets removed and the ball joints relocated. But if the ball joints are still good then just leave them in place and have the.

1999 Tahoe Ball Joint Replacement

How to Remove Bottom Ball Joint Rivets Step 1.

How to remove rivets lower ball joint. If you have to remove it then you need to get a spring compressor and remove the coil spring and shocks and it just got a little more involved. Support it well from underneath. I drilled all the way through the rivet being careful to keep the bit centered so I would not damage the A-arm and then carefully chisled off all three rivet heads on one side.

1994 GMC K1500 4WD 57L lower ball joint factory rivet removal without using an air hammer. Use a 1 8 in. Remove the wheels with the tire iron.

Drill out the three rivets retaining the ball joint to the lower control arm. The upper and lower ball joints on your vehicle and not riveted in. A air hammer works very well.

When I did my 93 upper and lower 16 rivets total I chose to very carefully with a cutting torch snip the rivet heads off let cool hit em a cut off wheel just enough to remove the slag and scale drill a 18 hole all the way out the bottom to let the flame through fire up the torch again and very carefully blow out just the rivet at least half of it then drift and hammer em out while still hot. There are lots of ideas out there to remove old rivets. Chisel off the head of the rivet using the air hammer.

In the video 1A Auto shows how to remove riveted ball joints using three different methods with different tools List of tools used Cutoff Wheel http. Then I hammered on. Some say grind this is fine as long as you take care as to not grind away your control arms.

Once the heads are gone then you punch them through. Finish drilling the head of the rivets with a 1 2 in. If you grind away the top of the rivets and then try to drill the insides of them out once thats gone you may get by without having to wail on it a lot.

3mm drill bit to make a pilot hole through the rivets. Unbolt the lower control arm ball joint from the steering knuckle using an open-end wrench. They are pressed in and you have to use a special ball joint press to remove and install them in your front axle.

Lift up the front of the vehicle using the jack and put it on jack stands. Loosen nut on top of ball jointseperate spindle assembly from ball joint wball joint seperating tool AKA pickle forkremove nutball joint is riveted to lower A frame-chisel off or drill out rivetsinstall new ball joint wnuts bolts supplied with it. Then using a punch I carefully hammered on each rivet to loosen them up.

Try heating up the edges of the rivets and then spraying some PB blaster on them - the fluid will wick in between the parts better a little bit risky because the pb blaster is flammable but I have used this as a last resort when I cant separate rust welded parts. My friend Ben ground the heads off the top of the rivets and it pretty much welded everything together on that side so we had to drill those 4 out. Failure to use the proper tool may cause damage to the ball joint and seal.

This will shock the metal and cause the control arm or spindle to simply fall off the ball joint. With everything out of the way you can remove the nut on the ball joint. Insert the pointed tip into the air hammer.

Place the tip of the air hammer attachment onto the area where the rivet was previously then pull the trigger and hammer the rivet through the lower control arm until the ball joint can be pulled out of the arm freely. You will then want to hit the side of the control arm or spindle where the ball joint is attached. I used a Dremel tool to cut slots into the rivet head make them look like a common screw and then cold chisel them off.

Remove whatever is needed to gain access to the ball joints. I figured out why we couldnt tap the rivets out on the drivers side. We moved on to the passenger side today and started drilling.

Support vehicle under A frame remove wheel. Most cars have riveted ball joints from factory and replacements are supplied with nuts and bolts screw on fittingThis method shows you how to easily remove. Then just punch out the rivets shanks.

Gm S10 Blazer Riveted Ball Joint Replacement Youtube