How To Remove A Thetford Toilet Pump

Visually check for damage turn the impellow using a very thin screwdriver and try it again. Be the first to review this product.

Thetford C260 Toilet Flush Pump Removal And Fix Youtube

I know I said I had checked everything but I missed the toilet.

How to remove a thetford toilet pump. Turn the toilet upside-down and install closet ﬂ ange seal. Use a flathead screwdriver to remove the toilet bolt covers if they are installed. Take the toilet out of the box.

There are usually two of these so you just have to do the same step to the other bolt covers. Prise the lid off the right hand lug to remove. To remove any Milton that is left.

Included should be the instructions for use and a holding tank cap. It needs quite a bit of effort using a thin bladed screwdriver under the sides. Lower toilet onto closet ﬂ ange until nuts on closet bolts go through rectangular holes in metal brackets seal rests on closet ﬂ ange and leg locates over locating disc.

Protect the top of the flush tank with something in case the screwdriver slips. The Control panel has corroded contacts. Genuine Thetford part for caravan motorhome or boat.

I have done all the neccessery tests required and proven that the pump for the toilet needs replacing i just cant find it there is no toilet rll holder in a panel where i was told it will be behind so just need to find out where the pump is. Thetford toilets usually have two toilet bolt covers. If the C2 bench type facing the toilet the flush blade opening button is on the left side on the right is the sunken toilet roll holder which pulls out but you may need to gently prise it out working around it smear vaselene around rim on replacing it make for easy removal underneath this is the pump in a cage held down by ONE cross head screw.

Cut the white wire insulation off so that the blue and brown wire stay intact and strip the blue and brown wire with the wire-stripper. Remove those and you can get inside the flush tank. To remove the pump you have to get underneath inside the compartment follow the water pipes remove the pipe s and the pump should come down.

To do this you will need to use a flathead screwdriver. Pull the seat lid out of its lug to the right. Depending on the model of the toilet there will either be a bolt cover at the front and back of the toilet or at the left and right side of the toilet.

Make sure white fork-shaped slides are in forward posi-tion. Cut the cable just above the pump with the combination pliers. Please click the below image to see our shipping and return policy.

Just put the tip of the screwdriver to the seams of the bolt cover and lift up. To remove them work on the right hand side as you look at the rear of the toilet. How do i change the pump thetford cassette toilet c-402.

In this video I replace the flush pump and show it. Once its free you can pull it forward and everything will then be loose and the other lug will just drop out. The toilet should be fixed to a vertical back wall.

After recently discovering my toilet flush pump was seized solid the only option was to replace the pump. This product hasnt received any reviews yet. Suitable for swivel type toilets.

So when removing your Thetford toilet you must remove it. Place the pump retainer and shrinktube on the new pump before. 12 volt toilet pump.

Remove the bolts using a half-inch socket wrench. Under the button cover theres a support plate with the 2 plastic posts that hold the top cover held in with 4 screws. Remove plastic bag with parts out of the bowl.

When a back wall is unavailable one will have to be installed see point 6 8 14. To remove the algae in the tank use a measured dose of Milton sterilising fluid give it a couple of hours then using the pump empty the tank this should clean the lot then fill with clean water you You could try adding some car shampoo and flush again. Undo that lift pump out You pull off the flush tube and cut the cable but you may find the problem is the impeller blade on the base of the pump.

The control switch and the pump needed replacing. In a recent trip our Thetford C260 toilet flush didnt work in this video i share how to remove the pump from a C260 toilet and demonstrate a common problem. This is a short vlog of how to do the jobT.

The Flush button is faulty. On my system Thetford C200 after removing the top coverthe toilet flush pump can simply be unclipped from inside the tank and the outlet hose.

Thetford 33368 Cassette Toilet Pump Walmart Com Walmart Com